Sky System One is the first in a line of 2.1 - integrated 3-way monitoring systems to be offered by Blue Sky International. Sky System One consists of two Blue Sky SAT 6.5 bi-amplified satellite speakers and a single 200-Watt powered Sub 12 subwoofer. Employing Blue Sky's proprietary computer-optimized crossover and bass-management networks, the Sky System One delivers seamless full range audio from the subwoofer to the main monitors with smooth on and off-axis frequency response. In addition, the Sky System One is THX pm3? Approved for use in THX pm3? Certified Studios and by adding three SAT 6.5s and a Blue Sky BMC, the system is easily expandable for use in a 5.1 monitoring setup.

General Specifications - SAT 6.5 Input Impedance 40k Ohms balanced Common Mode Rejection Ratio 40dB typical 60Hz Voltage Sensitivity 200mV = 90dB SPL @ 1M Maximum Input Level +24dBu balanced Frequency Response +/- 1.5dB 200 to 10kHz +/- 3.0dB 80 to 20kHz Low Frequency Cutoff 80Hz Low Frequency Rolloff 12dB per octave System Q 0.707 System Crossover Frequency 1.5kHz System Crossover Slope 4th order Linkwitz-Riley Acoustic Enclosure Solid 3/4" MDF construction with 1" front and rear baffle" Viscoelastic energy absorbing front baffle coating 1/4"x 20 inserts for attachment of OmniMount type 60 brackets (formerly known as the 100 Series). Dimensions are 12" H x 8" W x 10 1/4" D (11.88" with heatsink and tweeter wave guide) Weight 27lbs. 6 1/2" Hemispherical Woofer Long excursion design with a cast aluminum frame 1 1/2" aluminum voice coil with vented motor for high power handling Copper shorting ring for lower distortion. Ultra-Low power compression Mica filled polypropylene cone and rubber surround Fully video shielded 1" Tweeter Dual concentric diaphragm with integral wave guide High power handling neodymium motor structure Fully video shielded Sub 1Khz primary resonance Satellite Amplifier Discrete symmetrical bipolar design with localized feedback 100-Watts RMS into 4-Ohms for the woofer 100-Watts RMS into 4-Ohms for the tweeter THD + Noise less than 0.015% at rated output @1kHz XLR balanced input Adjustable gain control. Computer optimized crossover Measurement Data (Click to view response graph) View on axis frequency response. Measured at 2 meters, corrected to 1 meter. View on axis frequency response versus listening window. Listening window is an average of the +/- 15 degrees horizontal and +/- 15 vertical measurements. View on axis frequency response versus +/-15 degrees vertical. View on axis frequency response versus horizontal average. Horizontal average is comprised of +/15 degree and +/- 30 degree measurements. View on axis frequency response versus average of 0 and +/-15 degree vertical measurements. View on axis frequency response versus 15 and 30 degree horizontal measurements. General Specifications - Sub 12 All subwoofer measurements are measured using the subwoofer direct input, which does not have a low pass filter. Voltage Sensitivity 90dB SPL @ 100mv @ 1M (40 to 80Hz bandwidth limited) Frequency Response (anechoic) 30 to 200Hz +/-3dB Typical In-Room Response 20 to 200Hz (3000 Cubic Feet) Bass Management Section Input Impedance 20k Ohms balanced Common Mode Rejection Ratio 40dB typical @60Hz Maximum Input Level (all inputs) +24dBu balanced Maximum Output Level +24dBu balanced Output Impedance 200 Ohms balanced Auto Mute Time Out >15 Minutes Mute Threshold (all inputs) 30mV Left & Right Inputs to Sat Outputs Gain (balanced in and out) 0dB High-Pass Filter type 2nd order Linkwitz-Riley High-Pass Filter Cutoff 80Hz High-pass Filter Q 0.707 THD + Noise 0.002% @ 1kHz @ +4dBu Left & Right Inputs to Sub Out Gain 0dB Low-Pass Filter Type 4th order Linkwitz-Riley Low-Pass Cutoff 80Hz Subwoofer Direct In to Direct Output Gain 0dB Low-Pass Filter None Enclosure Solid 3/4" MDF construction with 1" MDF Front and Rear Baffle Viscoelastic energy absorbing front baffle coating Flush mounted driver Isolation feet are included. Inserts for optional attachment of spike feet. Dimensions are 18" H x 16" W x 20" D (22.07" with heatsink and grill) Weight 62lbs. 12" Woofer Long excursion design with cast aluminum frame. 2" voice coil with vented motor for high power handling Fully video shielded Subwoofer Amplifier Discrete symmetrical bipolar design with localized feedback 200-W RMS into 4 Ohms THD + Noise less than 0.015% at rated power @100Hz Adjustable gain control Measurement Data (Click to view response graph) View ground plane subwoofer measurement using direct input

Free 3-Year Warranty

Sound Pure stands behind our products. Free three-year warranty on this item. Coverage exclusions live in Terms & Conditions, Section 27.

Level of support and expertise that simply isn't available at big-box megastores. Read the warranty →

Returns

This item is not eligible for the Try-Before-You-Buy 48-hour audition. Standard return policy applies — see Terms & Conditions, Section 18 for details.